Power-Substation-Computers-DA-Series-Expansion-Modules-Moxa-vietnam.jpg

Power Substation Computers DA Series Expansion Modules Moxa vietnam


Features and BenefitsSubstation Reference Book

  • IRIG-B time-synchronization module
  • Universal PCI expansion module
  • 4-port 10/100 Mbps LAN module
  • 4-port 100 Mbps Fiber LAN module
  • 8-port 10/100 Mbps unmanaged switch module
  • 8-port RS-422/485 serial module with terminal block connectors
  • 8-port RS-232/422/485 software-selectable serial modules with isolation protection
  • Fully compatible with Moxa embedded computers that have peripheral expansion slots

 

 

Overview

Moxa’s peripheral expansion modules, which come with serial ports, LAN ports, switch ports, fiber ports, time-synchronization IRIG-B ports, and PCI slots, give end-users the greatest flexibility for setting up industrial applications and are fully compatible with Moxa’s embedded computers that have perpheral expansion slots.
The serial port modules include an 8-port RS-232/422/485 module with either DB9 or terminal block connectors, and an 8-port RS- 422/485 module with terminal block connectors. Some modules are even designed with 2 kV digital isolation, making them fully suitable for the great demands of industrial applications that use serial communication. In addition, a 4-port LAN module, 8-port switch module, and 4-port fiber LAN module are available for setting up industrial communication applications with Ethernet-based devices. A universal PCI development kit is also available for PCI-based devices for expanding industrial applications at a reasonable cost.
The time-synchronization module features 3 digital inputs and 4 digital outputs and provides precision timing information using IRIG-B input signals. The module is designed for embedded computers that support the PCI/104 interface.
All modules are designed to offer the greatest flexibility for setting up applications and performing industrial tasks. In particular, users can swap out modules quickly and easily.

White Paper

Making Smart Substations Even Smarter: Enhancing Substation Reliability, Availability, and Maintainability

Smart Substation Computer White PaperThis paper sketches out a few of the more important concerns that electricity suppliers should account for when planning substation upgrades. The focus is on how best to increase the reliability, availability, and maintainability of power substation automation networks within the context of the IEC 61850 vision, to give electricity suppliers a clear idea of the design procedures, device tolerances, and hardware and software features they should expect from the engineers and manufacturers who design and build their networking and computing devices.......more

-----------------------------------------------------------------------------------------------------------------------------------------------

White Paper

Using MMS and SNMP to Integrate IT Management for Substation Automation

Using MMS and SNMP to Integrate IT Management for Substation AutomationThe devices that electrical substation automation systems are built from depend on highly precise, time-critical communications. Substation thus often use highly specialized monitoring systems to tackle this problem, but can approach it using different technologies. The most up-to-date, “smart” substations use the Manufacturing Messaging Specification (MMS) for communications among IEC 61850 intelligent electronic devices (IEDs), allowing SCADA to monitor and control IED states as well as process switchgear and transformer data directly. However, IT networking devices have been increasingly applied in IEC 61850 systems, and this equipment communicates using SNMP. Consequently, in the modern substation automation industry it’s clear that, for the time being, SNMP and MMS will continue to exist side-by-side. For designers and integrators of electrical substation equipment, bringing both MMS and SNMP support to IT equipment is an ideal, one-size fits-all alternative that allows for the greatest flexibility and adaptability around........more

 

White Paper

Building the Industrial Cloud:The Immediate Future of M2M Technology

 

Building the Industrial Cloud:The Immediate Future of M2M TechnologyIn 2013, substantial steps towards building the Internet of Things at last began to materialize. In this white paper, Moxa examines the sorts of technology industrial networks will be relying on as they begin to build and deploy machine-to-machine networks. Software automations, hardware optimizations, and integrated platforms that fully exploit the convergence of these two main branches of system design are examined closely, to give IA and IT engineers a better idea of what challenges and obstacles they should be preparing for at the dawn of this new technological epoch........more

 -----------------------------------------------------------------------------------------------------------------------------------------------

DA-LN04-RJ Hardware Specifications
Ethernet Interface
LAN 4 auto-sensing 10/100 Mbps ports (RJ45)
Magnetic Isolation Protection 1.5 kV built-in
Physical Characteristics
Weight 198 g (0.44 lb)
Dimensions 132 x 150 x 42 mm (5.20 x 5.91 x 1.65 in)
DA-SW08-RJ Hardware Specifications
Ethernet Interface
LAN 8 auto-sensing 10/100 Mbps unmanaged Ethernet switch ports (RJ45)
Magnetic Isolation Protection 1.5 kV built-in
Physical Characteristics
Weight 200 g (0.44 lb)
Dimensions 132 x 150 x 42 mm (5.20 x 5.91 x 1.65 in)
DA-UPCI-DK Hardware Specifications
Universal PCI Expansion Adatper
PCI Slots 1
Interface Bus 32-bit Universal PCI (3.3 V and 5 V)
Physical Characteristics
Weight 195 g (0.43)
Dimensions 132 x 150 x 42 mm (5.20 x 5.91 x 1.65 in)
MTBF (mean time between failures) 11,053,266 hrs
DA-FX04-MM-ST-T Hardware Specifications
Fiber Interface
Number of Ports 4 (100BaseFX)
Fiber Mode Multi-mode
Connector Type ST
Optical Wavelength 0 to 2 km, 1310 nm (62.5/125 μm, 500 MHz*km)
Min-TX Output -20 dBm
Max-TX Output -14 dBm
RX Sensitivity -34 dBm
Physical Characteristics
Weight 495 g (1.10 lb)
Dimensions 132 x 150 x 42 mm (5.20 x 5.91 x 1.65 in)
Environmental Limits
Operating Temperature -40 to 70°C (-40 to 158°F)
Standards and Certifications
EMC EMC Level 4, ESD Level 4, criteria A
Software Functions
IEEE 1588 or IP Teaming Selectable (Default =IP Teaming) Supports 4 modes
AFT Adapter Failover Teaming
SFT Switch Fault Tolerance
ALB Adapter Failover and Load Balancing
Link Aggregation supported
DA-IRIGB-4DIO-PCI104-EMC4 Hardware Specifications
Hardware
Communication Controller FPGA Cyclone V
Form Factor PCI/104
Time Code Input
IRIG-B Based on the IRIG STANDARD 200-04 and IEEE 1344
Precision and Accuracy
Accuracy (Time Synchronization) ±1 µs
Accuracy (Free Running) ±500 ms @ 24 hr
Input Signals
Single Level • Open: High
• Short to GND:> Low
• Level Input: 5 to 12 V
Differential Level • D+ - D- > 0.2 V, RXD is High
• D+ - D- < -0.2 V, RXD is Low
• Level Input: 5 V
Interface
IRIG-B 2-pin wafer to DB9
DI/DO 10-pin wafter to DB9
Protection
ESD Protection 8 kV contact, 15 kV Air ESD protection
Surge Protection 2 kV line-to-line and 4 kV line-to-ground surge protection, 8/20 µs waveform
Insulation 500 V
Digital Input
Input Channels 3, source type
Input Voltage 0 to 30 VDC
Digital Input Levels for Dry Contacts • Logic level 0: Close to GND
• Logic level 1: Open
Digital Input Levels for Wet Contacts • Logic level 0: +3 V max.
• Logic level 1: +10 V to +30 V (source to DI)
Isolation 3 kV optical isolation
Connector Type DB9 male
Digital Output
Output Channels 4, sink type
Output Current Max. 200 mA per channel
On-state Voltage 24 VDC nominal, open collector to 30 V
Isolation 3 kV optical isolation
Connector Type Male
Operating Systems
Windows Windows 7E
Linux Debian 7
Physical Characteristics
Dimensions 90 x 96 mm (3.54 x 3.78 in)
Environmental Limits
Operating Temperature -10 to 60°C (14 to 140°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Altitude Up to 2000 m
Standards and Certifications
EMC CE, FCC
EMI EN 55032, EN 61000-3-2, EN 61000-3-3, FCC Part 15 Subpart B Class A
EMS IEC 61000-4-2 ESD: Contact 8 kV; Air 15 kV
IEC 61000-4-3 RS: 10 V/m (80 MHz to 1 GHz)
IEC 61000-4-4 EFT: Signal 4 kV
IEC 61000-4-5 Surge: Signal 4 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8
Green Product RoHS, CRoHS, WEEE
DA-SP08-DB, DA-SP08-I-DB, DA-SP08-I-TB Hardware Specifications
Serial Interface
Serial Standards 8 RS-232/422/485 ports, software selectable (DB9 male or terminal block connector)
ESD Protection 15 kV for all signals
Isolation 2 kV digital isolation (DA-SP08-I-DB and DA-SP08-I-TB only)
Serial Communication Parameters
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Even, Odd, Space, Mark
Flow Control RTS/CTS, XON/XOFF, ADDC® (automatic data direction control) for RS-485
Baudrate 50 bps to 921.6 kbps (supports non-standard baudrates; see user’s manual for details)
Serial Signals
RS-232 TxD, RxD, DTR, DSR, RTS, CTS, DCD, GND
RS-422 TxD+, TxD-, RxD+, RxD-, GND
RS-485-4w TxD+, TxD-, RxD+, RxD-, GND
RS-485-2w Data+, Data-, GND
Physical Characteristics
Weight 290 g (0.64 lb)
Dimensions 130 x 150 x 42 mm (5.12 x 5.91 x 1.65 in)
MTBF (mean time between failures) 1,753,143 hrs
DA-SP08-I-EMC4-DB/TB Hardware Specifications
Serial Interface
Serial Standards 8 RS-232/422/485 ports, software selectable (DB9 male or terminal block connector)
ESD Protection 8 kV contact, 15 kV air
Surge Protection 2 kV line-to-line and 4 kV line-to-ground surge protection, 8/20 μs waveform
Insulation 500 V
Isolation 2 kV digital isolation
Pull low/high 1k/150k, jumper selectable
Termination Resistor 120 ohms, jumper selectable
Serial Communication Parameters
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Even, Odd, Space, Mark
Flow Control RTS/CTS, XON/XOFF, ADDC® (automatic data direction control) for RS-485
Baudrate 50 bps to 921.6 kbps (supports non-standard baudrates; see user’s manual for details)
Serial Signals
RS-232 TxD, RxD, RTS, CTS, GND
RS-422 TxD+, TxD-, RxD+, RxD-, GND
RS-485-4w TxD+, TxD-, RxD+, RxD-, GND
RS-485-2w Data+, Data-, GND
Physical Characteristics
Weight 500 g (1.11 lb)
Dimensions 130 x 150 x 42 mm (5.12 x 5.91 x 1.65 in)
MTBF (mean time between failures) 1,753,143 hrs
DA-SP38-I-TB Hardware Specifications
Serial Interface
Serial Standards 8 RS-422/485 ports, software selectable (DB9 male or terminal block connector)
ESD Protection 15 kV for all signals
Isolation 2 kV digital isolation
Serial Communication Parameters
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Even, Odd, Space, Mark
Flow Control RTS/CTS, XON/XOFF, ADDC® (automatic data direction control) for RS-485
Baudrate 50 bps to 921.6 kbps (supports non-standard baudrates; see user’s manual for details)
Serial Signals
RS-422 TxD+, TxD-, RxD+, RxD-, GND
RS-485-4w TxD+, TxD-, RxD+, RxD-, GND
RS-485-2w Data+, Data-, GND
Physical Characteristics
Weight 245 g (0.54 lb)
Dimensions 130 x 150 x 42 mm (5.12 x 5.91 x 1.65 in)